AOpen DE7200 Series Instruções de Operação Página 89
- Página / 167
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MAINTENANCE
31 Dec 13 5-27
DE-7200VFDCentrifuge
ALARM AND FAULT MESSAGES
Cause Corrective Action
F1017 - Bowl VFD Drive OL Alarm, Ref Troubleshooting Section of User Manual
Feed rate causing overload Reduce feed rate or reduce bowl speed.
Bowl drive motor drawing excessive
current
Replace motor if defective.
F1021 - Bowl Motor Thermal Overload Check Bowl Motor Temperature and Thermistor
Bowl drive motor shut down due to high
temperature or defective thermistor in
motor winding
Check motor temperature. Allow motor to cool, and
then check for continuity across thermistor leads. If
open circuit is found, replace motor.
Bad connection(s) Check connections at TB2-7 and 8, at
transmitter/intrinsic barrier, and at conveyor VFD.
Correct as required. Replace motor if no defects are
found.
F2000 - Conveyor Clutch Tripped, Allow Centrifuge to Stop Completely, then Reset
Clutch
Conveyor torque has exceeded pre-set
limit causing clutch to trip
Allow bowl to come to a complete standstill, and then
reset clutch as described under Automatic Shutdown
in Section 4.
F2001 - Conveyor High Torque Alarm, Reduce Feed Rate
Conveyor torque exceeds pre-set limit Reduce feed rate and/or increase differential speed.
F2002 - Conveyor High Torque Fault and Shutdown, Perform Cleanout and Reduce Feed
Rate
Conveyor torque exceeds pre-set limit After bowl has stopped rotating, perform cleanout
procedure to remove solids buildup, and re-start
centrifuge at reduced feed rate and/or higher
differential speed.
F2010 - Conveyor VFD Communications Error
Communication lost between conveyor
VFD and PLC
Confirm that green LED next to Ethernet cable on
Ethernet switch is lighted, indicating that hub is
functional.
Check connections between conveyor VFD and
PLC, and correct any defects.
Replace conveyor VFD communication module, if no
other defect is found.
F2011 - Conveyor VFD Alarm, Ref Troubleshooting Section of User Manual
Conveyor VFD alarm Identify alarm from operator control panel. Perform
indicated corrective action.
- DE-7200 Centrifuge 1
- CONTENTS 5
- Section 6
- CONTENTS 7
- SECTION 1 - INTRODUCTION 9
- EQUIPMENT USE 10
- DESCRIPTION 10
- Rotating Assembly 11
- Drive Motors 12
- Control Cabinet 12
- Case and Base 13
- Vibration Switch 13
- MECHANICAL OPERATION 14
- CONTROL SYSTEM 15
- PRODUCT SUPPORT 16
- CONTACT INFORMATION 16
- SECTION 2 - SAFETY 17
- Equipment Handling 18
- Maintenance 19
- Storage 19
- MSDS’S (CONT’D) 20
- SECTION 3 - INSTALLATION 21
- STORAGE 22
- Rotating Assembly and Motors 22
- INSTALLATION SEQUENCE 23
- EQUIPMENT HANDLING 24
- EQUIPMENT HANDLING (CONT’D) 26
- Liquid Discharge 29
- Solid Discharge Chute 29
- EQUIPMENT LEVELING 29
- FEED AND FLUSH CONNECTIONS 31
- COMPRESSED AIR 33
- FEED PUMP 33
- ELECTRIC POWER CONNECTIONS 33
- Connection Options 33
- POLARITY TEST 36
- SENSOR CONNECTIONS 37
- MACHINE STARTUP 38
- GENERAL 39
- SOFTWARE VERSION 39
- OPERATING SAFETY 39
- Purge System Bypass 40
- INITIAL STARTUP 41
- INITIAL STARTUP (CONT’D) 42
- OPERATING INSTRUCTIONS 43
- NORMAL STARTUP 44
- COLD CLIMATE STARTUP 45
- OPERATION 45
- Bowl Speed 47
- Conveyor Differential Speed 47
- Pond Depth 47
- Pond Depth (Cont’d) 48
- BEARING TEMPERATURES 50
- MOTOR TORQUE TREND 50
- SYSTEM DIAGNOSTICS 51
- PERFORMANCE STATUS 51
- ALARM AND FAULT MESSAGES 52
- VFD STATUS 53
- VFD STATUS (CONT’D) 54
- PUMP VFD FAULT STATUS 54
- VFD TEMPERATURE TRENDS 55
- VFD FAULT RESET 55
- VFD FAULT RESET (CONT’D) 56
- SETUP SCREEN 56
- PUMP SETUP SCREEN 57
- CLEAN OUT 57
- CLEAN OUT (CONT’D) 58
- Automatic Cleanout 58
- Manual Cleanout 58
- NORMAL SHUTDOWN 59
- AUTOMATIC SHUTDOWN 59
- Excessive Vibration 59
- Main Bearing Temperatures 59
- Excessive Bowl Speed 60
- Conveyor Clutch Trip 60
- EMERGENCY SHUTDOWN 61
- Electric Power Shutdown 61
- Mechanical Shutdown 61
- SECTION 5 - MAINTENANCE 63
- PREVENTIVE MAINTENANCE 64
- LUBRICATION CHART 65
- GEARBOX OIL LEVEL CHECK 65
- GEARBOX OIL CHANGE 66
- DRIVE BELT REPLACEMENT 67
- PURGE SYSTEM 69
- Bypassing Purge System 69
- Initial Purge Time Setting 70
- Leakage Compensation Test 71
- Rotating Assembly Removal 73
- Cleaning and Inspection 75
- Installation 76
- RECOMMENDED SPARE PARTS 77
- TROUBLESHOOTING 79
- Troubleshooting Procedure 79
- TROUBLESHOOTING (CONT’D) 80
- Troubleshooting Chart 80
- CONTROL COMPONENT INDICATORS 98
- MAINTENANCE 100
- DE-7200VFDCentrifuge 103
- CONTROL ENCLOSURE ASSEMBLY 141
- DE-7200 EX-PROOF 460/480/60/3 141
- 16472-00-002 141
- DE-7200 EX-PROOF 380/400/3 143
- 16472-00-003 143
- DE-7200 EX-PROOF 575/600/60/3 145
- 16472-00-004 145
- DE-7200 460/480/60/3 147
- 16472-00-005 147
- PURPOSE 149
- DE-7200VFDCentrifuge 150
- INSTALLATION 156
- HMI Server Installation 156
- Electric Power Connections 156
- Ethernet Connections 157
- Appendix A-HMIServerSystem 158
- OPERATING HMI SERVER 159
- Startup and Shutdown 159
- Operation 159
- Operation (Cont’d) 160
- REFERENCE DRAWINGS 164
Manuais e produtos relacionados com Barebones PC/estação de trabalho AOpen DE7200 Series
(11 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais